3A Series MODULAR AC & DC LOADS

Model : 3A Series

Q'ty :

3A Series MODULAR AC & DC LOADS

The 3A Series modular AC and DC loads allow mulit-channel load systems to be configured with easy.

Modules are available for 60Vrms, 150Vrms or 300Vrms. This supports testing of low voltage AC products as well as those intended for use in 120Vac countries like the US or 230Vac geographies like Asia and Europe. All 3A Series modules support 300VA or 300W of dissipation and it is possible to parallel modules for higher load requirements. Mainframes in the 3A Series can accommodate 1 or 4 modules with a maximum 1200VA of AC load capability.

For questions regarding the 3A Series AC and DC Loads, please contact us.

The Adaptive Power 3A Series of Programmable AC & DC Electronic Load Modules are ideally suited for testing AC products such as UPS, DC/AC inverters and AC power supplies. These loads not only handle sinusoidal AC input voltage but also non-sinusoidal voltages and highly distorted waveforms as often found on UPS outputs or inexpensive DC/AC inverters.

The high power density of the 3A Series allows up to four loads to be installed in a single 19″ wide rack-mount mainframe. For lesser demands, a single slot mainframe is available as well.

The 3A Series consists of a total of three different modules providing a variation of possible voltages choices.

Single Channel Modules

Model	3A060-20		3A150-08		3A300-04
OPERATING RANGES
Power Ranges	0 – 300 VA		0 – 300 VA		0 – 300 VA
Current Ranges	0 -10 Arms	10 -20 Arms	0 – 4 Arms	4 – 8 Arms	0 – 2 Arms	2 – 4 Arms
Voltage Ranges	10 – 60 Vrms/Vdc		15 – 150 Vrms/Vdc		30 – 300 Vrms/Vdc
Frequency	DC, 40 – 400Hz (CC Mode) / DC – 400Hz (LIN,CR Mode)
OPERATING MODES	Constant Current (CC), Linear CC (LCC), Constant Resistance (CR), CREST FACTOR (CF) (in CC Mode only)
PROTECTION	Over Power (OP), Over Current (OC), Over Voltage (OV), Over Temperature (OT))
CREST & POWER FACTOR RANGE
Lagging PF	CF: √2 to 3.5 . PF: – 0.30 to -0.85
Leading PF	CF: √2 to 3.5 . PF: + 0.30 to +0.85 or 1.00
METERING
Voltage Range	0 – 60 V		0 – 150 V		0 – 300 V
Current Range	0 – 20 A		0 – 8 A		0 – 4 A
Power Range	0 – 300 W
VA Range	0 – 300 W
OTHER SPECIFICATIONS
Current Monitor	5 A/V		2 A/V		1 A/V
Dimensions (HxWxD)	143 x 108 x 405 mm / 5.6″ x 4.25″ x 15.9″
Weight (Net, Module)	3.5kg / 7.7 lbs

Mainframes

Mainframe	34M01	34M01-01	34M04	34M04-01
No. of Slots	1	1	4	4
Supports	3A060-20, 3A150-08, 3A300-04
Max Power	300 VA		1200 VA
Remote Interface	RS232	RS232 + GPIB	RS232	RS232 + GPIB
AC Input	100-115Vac ±10% or 200-230Vac ±10%
Frequency	50 / 60 Hz ±3Hz
Max Power Consumption	40 W		100 W
Dimensions (WxHxD)	150 x 177 x 445 mm 5.9 x 7.0 x 17.5″		440 x 177 x 445 mm 17.3 x 7.0 x 17.5″
Weight	5.5 kg / 12.1 lbs		9.3 kg / 20.5 lbs

Max. Power 300VA or 300W per Module
Both AC and DC operating modes
Voltage Range Choices, 60, 150 or 300Vac
Sine, Square and Step Sine Support
Up to 4 AC Load Inputs per Mainframe
Parallel Modules to 1200VA
Synchronized Operation of Multiple Loads
High-Speed 4½ Digit Precision Metering Capability
Operating Modes: Constant Current (CC), Linear Constant Current (LCC), Constant Resistance (CR) and Crest Factor (CF) control
Leading and Lagging Power Factor (PF)
150 Sets of Store/Recall Memory
Go/NoGo Limit Test Mode
AC Current Monitor Output Signal
RS232 and GPIB Interfaces
CE Mark

Load Versatility

All ASP 3A Series Loads are equipped with a powerful microcontroller and user friendly controls to provide capabilities that cover a wide range of load applications. Built in metering of Voltage, Current, Power and Resistance standard. With its ability to operate in both AC or DC mode, the 3A Series provides great versatility for any lab or test floor.

AC Power Source Testing (AC Mode)

With its ability to simulate various power factor and crest factor AC load conditions, the APS 3A Series is an excellent real-world test solution for AC Power Sources and any other DC/AC inverter or AC/AC converter product. With up to four AC load channels per mainframe, high speed testing of AC products can be accommodated with four units being tested simultaneously, achieving significant test throughput in high voltage production environments.

DC Inverter Supply Design (AC Mode)

With built-in features like over current protection (OPC) test and over power protection (OPP) test and dynamic constant current waveform testing, new power supply designs can be thoroughly evaluated against design specifications. An analog input mode allows arbitrary current waveforms to be applied to a unit under test as well.

Battery Charge/Discharge Testing (DC Mode)

Using the DC load mode, specific discharge current levels can be set as a function of battery voltage. This allows characterization and performance testing of various battery chemistries. AC/DC supplies and inverters can be tested in DC mode as well.