15kV ESD Simulator
dito - the ultimate ESD tester
Electrostatic discharges either from a human body to any other part or between two different objects can cause persistent disturbances or even destruction to sensitive electronics or controls. Voltages of several 1,000 volts are generated.
dito is the most advanced ESD tester to simulate ESD pulses as per EN/IEC 61000-4-2 and other standards requirements.
- Most ergonomic design
- Light weight (870g)
- Interchangeable discharge tips
- Interchangeable R/C networks
- LiFePO4 power booster to perform long duration tests
- Library of standard test routines
- Test voltage measurement and control
- Various test routines for testing and evaluation
- High-sophisticated user guidance by test plans created by esd.control software
- Optional fiber optic link between dito and computer (USB port)

It is unlike any other ESD generators. Its ergonomic design is recognised to be more user-friendly. There is no part of dito that hides the discharge tip while watching the display or operating the dito. You see where you point the tip no matter how you direct dito to the DUT.
The discharge voltage is measured and recorded. Discharge is stopped automatically when battery voltage becomes low. The user is informed when dito cannot charge properly. All this helps to assure reliable and reproducible tests without any question mark and doubt.
Discharge tips and discharge networks can easily be changed without disassembling the dito; simply remove one and plug-on another tip or module. The discharge modules are automatically recognised and the R/C configuration is shown in the display. You just can't use a wrong discharge network!
Easy to operate

esd.control - More than a remote control and documentation software
esd.control goes far beyond being just a remote control and documentation software. It is your ESD Test Manager from A to Z. It covers the preparation of the test (definition of the test plan, including all test points and the generation of test notes), test routine programming, collection of test data and full documentation of every step. esd.control is the state-of-the-art software tool for ESD testing.
Additionally, a fiber optic link is offered as an option to communicate with the dito separating the sensitive computer from the test set-up and to avoid ground loops.
Other Models
The ESD Simulator Series
The EM TEST ESD simulator series addresses a wide range of test applications from various areas for voltages up to 30kV for both air and contact discharge. Complemented by its esd.control software both ESD NX30 and dito become a real ESD test system supporting the user from planning the test until full documentation of the test results.
Accessories
RFCI Fast Relay Module for Special ESD Tests
The Fast Relay module, type RFCI, is introduced to perform ESD tests with pulses having a faster rise time than required as per EN/IEC 61000-4-2. Rise time is specified to be between 200ps and 300ps. This special requirement originates from the computer industry.
Calibration target set CTR 2 for waveform verification as per EN/IEC 61000-4-2
The CTR 2 calibration target and its accessories like 20dB attenuator and coaxial cable forms the set to verify the ESD waveform as requested by the standard EN/IEC 61000-4-2. The 2ohm target is built following the specification of the standard.
Chrysler PF-9326
DaimlerChrysler PF-10540
EN 300329
EN 300340
EN 300342-1
EN 300386 V1.3.2
EN 301489-1
EN 301489-17
EN 301489-24
EN 301489-7
EN 55024
EN 61000-4-2
Fiat 9.90110
Ford EMC-CS-2009.1
Ford ES-XW7T-1A278-AB
Ford ES-XW7T-1A278-AC
Ford WDR 00.00EA
IEC 61000-4-2
IEC 61326
ISO 10605
ITU-T K.20
ITU-T K.21
ITU-T K.45
JASO D001-94
MIL STD 461 G CS 118
Renault 36.00.400/B
Renault 36.00.400/C
Toyota TSC3500G
Toyota TSC3590G
Volvo EMC Requirements (1998)